Инструменты пользователя

Инструменты сайта


motion

Различия

Здесь показаны различия между двумя версиями данной страницы.

Ссылка на это сравнение

motion [2017/05/29 16:32] (текущий)
Sergey Kondrashov создано
Строка 1: Строка 1:
 +<​code>​
 +# Rename this distribution example file to motion.conf
 +#
 +# This config file was generated by motion 3.2.12+git20140228
  
 +
 +############################################################​
 +# Daemon
 +############################################################​
 +
 +# Start in daemon (background) mode and release terminal (default: off)
 +daemon on
 +
 +# File to store the process ID, also called pid file. (default: not defined)
 +process_id_file /​var/​run/​motion/​motion.pid
 +
 +############################################################​
 +# Basic Setup Mode
 +############################################################​
 +
 +# Start in Setup-Mode, daemon disabled. (default: off)
 +setup_mode off
 +
 +
 +# Use a file to save logs messages, if not defined stderr and syslog is used. (default: not defined)
 +;logfile /​tmp/​motion.log
 +
 +# Level of log messages [1..9] (EMR, ALR, CRT, ERR, WRN, NTC, INF, DBG, ALL). (default: 6 / NTC)
 +log_level 6
 +
 +# Filter to log messages by type (COR, STR, ENC, NET, DBL, EVT, TRK, VID, ALL). (default: ALL)
 +log_type all
 +
 +###########################################################​
 +# Capture device options
 +############################################################​
 +
 +# Videodevice to be used for capturing ​ (default /​dev/​video0)
 +# for FreeBSD default is /dev/bktr0
 +videodevice /dev/video0
 +
 +# v4l2_palette allows to choose preferable palette to be use by motion
 +# to capture from those supported by your videodevice. (default: 17)
 +# E.g. if your videodevice supports both V4L2_PIX_FMT_SBGGR8 and
 +# V4L2_PIX_FMT_MJPEG then motion will by default use V4L2_PIX_FMT_MJPEG.
 +# Setting v4l2_palette to 2 forces motion to use V4L2_PIX_FMT_SBGGR8
 +# instead.
 +#
 +# Values :
 +# V4L2_PIX_FMT_SN9C10X : 0  '​S910'​
 +# V4L2_PIX_FMT_SBGGR16 : 1  '​BYR2'​
 +# V4L2_PIX_FMT_SBGGR8 ​ : 2  '​BA81'​
 +# V4L2_PIX_FMT_SPCA561 : 3  '​S561'​
 +# V4L2_PIX_FMT_SGBRG8 ​ : 4  '​GBRG'​
 +# V4L2_PIX_FMT_SGRBG8 ​ : 5  '​GRBG'​
 +# V4L2_PIX_FMT_PAC207 ​ : 6  '​P207'​
 +# V4L2_PIX_FMT_PJPG ​   : 7  '​PJPG'​
 +# V4L2_PIX_FMT_MJPEG ​  : 8  '​MJPEG'​
 +# V4L2_PIX_FMT_JPEG ​   : 9  '​JPEG'​
 +# V4L2_PIX_FMT_RGB24 ​  : 10 '​RGB3'​
 +# V4L2_PIX_FMT_SPCA501 : 11 '​S501'​
 +# V4L2_PIX_FMT_SPCA505 : 12 '​S505'​
 +# V4L2_PIX_FMT_SPCA508 : 13 '​S508'​
 +# V4L2_PIX_FMT_UYVY ​   : 14 '​UYVY'​
 +# V4L2_PIX_FMT_YUYV ​   : 15 '​YUYV'​
 +# V4L2_PIX_FMT_YUV422P : 16 '​422P'​
 +# V4L2_PIX_FMT_YUV420 ​ : 17 '​YU12'​
 +#
 +v4l2_palette 17
 +
 +# Tuner device to be used for capturing using tuner as source (default /​dev/​tuner0)
 +# This is ONLY used for FreeBSD. Leave it commented out for Linux
 +; tunerdevice /dev/tuner0
 +
 +# The video input to be used (default: -1)
 +# Should normally be set to 0 or 1 for video/TV cards, and -1 for USB cameras
 +input -1
 +
 +# The video norm to use (only for video capture and TV tuner cards)
 +# Values: 0 (PAL), 1 (NTSC), 2 (SECAM), 3 (PAL NC no colour). Default: 0 (PAL)
 +norm 0
 +
 +# The frequency to set the tuner to (kHz) (only for TV tuner cards) (default: 0)
 +frequency 0
 +
 +# Rotate image this number of degrees. The rotation affects all saved images as
 +# well as movies. Valid values: 0 (default = no rotation), 90, 180 and 270.
 +rotate 0
 +
 +# Image width (pixels). Valid range: Camera dependent, default: 352
 +width 320
 +
 +# Image height (pixels). Valid range: Camera dependent, default: 288
 +height 240
 +
 +# Maximum number of frames to be captured per second.
 +# Valid range: 2-100. Default: 100 (almost no limit).
 +framerate 12
 +
 +# Minimum time in seconds between capturing picture frames from the camera.
 +# Default: 0 = disabled - the capture rate is given by the camera framerate.
 +# This option is used when you want to capture images at a rate lower than 2 per second.
 +minimum_frame_time 0
 +
 +# URL to use if you are using a network camera, size will be autodetected (incl http:// ftp:// mjpg:// rstp:// or file:///)
 +# Must be a URL that returns single jpeg pictures or a raw mjpeg stream. Default: Not defined
 +; netcam_url value
 +
 +# Username and password for network camera (only if required). Default: not defined
 +# Syntax is user:​password
 +; netcam_userpass value
 +
 +# The setting for keep-alive of network socket, should improve performance on compatible net cameras.
 +# off:   The historical implementation using HTTP/1.0, closing the socket after each http request.
 +# force: Use HTTP/1.0 requests with keep alive header to reuse the same connection.
 +# on:    Use HTTP/1.1 requests that support keep alive as default.
 +# Default: off
 +netcam_keepalive off
 +
 +# URL to use for a netcam proxy server, if required, e.g. "​http://​myproxy"​.
 +# If a port number other than 80 is needed, use "​http://​myproxy:​1234"​.
 +# Default: not defined
 +; netcam_proxy value
 +
 +# Set less strict jpeg checks for network cameras with a poor/buggy firmware.
 +# Default: off
 +netcam_tolerant_check off
 +
 +# Let motion regulate the brightness of a video device (default: off).
 +# The auto_brightness feature uses the brightness option as its target value.
 +# If brightness is zero auto_brightness will adjust to average brightness value 128.
 +# Only recommended for cameras without auto brightness
 +auto_brightness off
 +
 +# Set the initial brightness of a video device.
 +# If auto_brightness is enabled, this value defines the average brightness level
 +# which Motion will try and adjust to.
 +# Valid range 0-255, default 0 = disabled
 +brightness 0
 +
 +# Set the contrast of a video device.
 +# Valid range 0-255, default 0 = disabled
 +contrast 0
 +
 +# Set the saturation of a video device.
 +# Valid range 0-255, default 0 = disabled
 +saturation 0
 +
 +# Set the hue of a video device (NTSC feature).
 +# Valid range 0-255, default 0 = disabled
 +hue 0
 +
 +
 +############################################################​
 +# Round Robin (multiple inputs on same video device name)
 +############################################################​
 +
 +# Number of frames to capture in each roundrobin step (default: 1)
 +roundrobin_frames 1
 +
 +# Number of frames to skip before each roundrobin step (default: 1)
 +roundrobin_skip 1
 +
 +# Try to filter out noise generated by roundrobin (default: off)
 +switchfilter off
 +
 +
 +############################################################​
 +# Motion Detection Settings:
 +############################################################​
 +
 +# Threshold for number of changed pixels in an image that
 +# triggers motion detection (default: 1500)
 +threshold 1500
 +
 +# Automatically tune the threshold down if possible (default: off)
 +threshold_tune off
 +
 +# Noise threshold for the motion detection (default: 32)
 +noise_level 32
 +
 +# Automatically tune the noise threshold (default: on)
 +noise_tune on
 +
 +# Despeckle motion image using (e)rode or (d)ilate or (l)abel (Default: not defined)
 +# Recommended value is EedDl. Any combination (and number of) of E, e, d, and D is valid.
 +# (l)abeling must only be used once and the '​l'​ must be the last letter.
 +# Comment out to disable
 +despeckle_filter EedDl
 +
 +# Detect motion in predefined areas (1 - 9). Areas are numbered like that:  1 2 3
 +# A script (on_area_detected) is started immediately when motion is         4 5 6
 +# detected in one of the given areas, but only once during an event. ​       7 8 9
 +# One or more areas can be specified with this option. Take care: This option
 +# does NOT restrict detection to these areas! (Default: not defined)
 +; area_detect value
 +
 +# PGM file to use as a sensitivity mask.
 +# Full path name to. (Default: not defined)
 +; mask_file value
 +
 +# Dynamically create a mask file during operation (default: 0)
 +# Adjust speed of mask changes from 0 (off) to 10 (fast)
 +smart_mask_speed 0
 +
 +# Ignore sudden massive light intensity changes given as a percentage of the picture
 +# area that changed intensity. Valid range: 0 - 100 , default: 0 = disabled
 +lightswitch 0
 +
 +# Picture frames must contain motion at least the specified number of frames
 +# in a row before they are detected as true motion. At the default of 1, all
 +# motion is detected. Valid range: 1 to thousands, recommended 1-5
 +minimum_motion_frames 1
 +
 +# Specifies the number of pre-captured (buffered) pictures from before motion
 +# was detected that will be output at motion detection.
 +# Recommended range: 0 to 5 (default: 0)
 +# Do not use large values! Large values will cause Motion to skip video frames and
 +# cause unsmooth movies. To smooth movies use larger values of post_capture instead.
 +pre_capture 0
 +
 +# Number of frames to capture after motion is no longer detected (default: 0)
 +post_capture 0
 +
 +# Event Gap is the seconds of no motion detection that triggers the end of an event.
 +# An event is defined as a series of motion images taken within a short timeframe.
 +# Recommended value is 60 seconds (Default). The value -1 is allowed and disables
 +# events causing all Motion to be written to one single movie file and no pre_capture.
 +# If set to 0, motion is running in gapless mode. Movies don't have gaps anymore. An
 +# event ends right after no more motion is detected and post_capture is over.
 +event_gap 60
 +
 +# Maximum length in seconds of a movie
 +# When value is exceeded a new movie file is created. (Default: 0 = infinite)
 +max_movie_time 0
 +
 +# Always save images even if there was no motion (default: off)
 +emulate_motion off
 +
 +
 +############################################################​
 +# Image File Output
 +############################################################​
 +
 +# Output '​normal'​ pictures when motion is detected (default: on)
 +# Valid values: on, off, first, best, center
 +# When set to '​first',​ only the first picture of an event is saved.
 +# Picture with most motion of an event is saved when set to '​best'​.
 +# Picture woutpuith motion nearest center of picture is saved when set to '​center'​.
 +# Can be used as preview shot for the corresponding movie.
 +output_pictures on
 +
 +# Output pictures with only the pixels moving object (ghost images) (default: off)
 +output_debug_pictures off
 +
 +# The quality (in percent) to be used by the jpeg compression (default: 75)
 +quality 65
 +
 +# Type of output images
 +# Valid values: jpeg, ppm (default: jpeg)
 +picture_type jpeg
 +
 +############################################################​
 +# FFMPEG related options
 +# Film (movies) file output, and deinterlacing of the video input
 +# The options movie_filename and timelapse_filename are also used
 +# by the ffmpeg feature
 +############################################################​
 +
 +# Use ffmpeg to encode movies in realtime (default: off)
 +ffmpeg_output_movies on
 +
 +# Use ffmpeg to make movies with only the pixels moving
 +# object (ghost images) (default: off)
 +ffmpeg_output_debug_movies off
 +
 +# Use ffmpeg to encode a timelapse movie
 +# Default value 0 = off - else save frame every Nth second
 +ffmpeg_timelapse 0
 +
 +# The file rollover mode of the timelapse video
 +# Valid values: hourly, daily (default), weekly-sunday,​ weekly-monday,​ monthly, manual
 +ffmpeg_timelapse_mode daily
 +
 +# Bitrate to be used by the ffmpeg encoder (default: 400000)
 +# This option is ignored if ffmpeg_variable_bitrate is not 0 (disabled)
 +ffmpeg_bps 500000
 +
 +# Enables and defines variable bitrate for the ffmpeg encoder.
 +# ffmpeg_bps is ignored if variable bitrate is enabled.
 +# Valid values: 0 (default) = fixed bitrate defined by ffmpeg_bps,
 +# or the range 2 - 31 where 2 means best quality and 31 is worst.
 +ffmpeg_variable_bitrate 0
 +
 +# Codec to used by ffmpeg for the video compression.
 +# Timelapse mpegs are always made in mpeg1 format independent from this option.
 +# Supported formats are: mpeg1 (ffmpeg-0.4.8 only), mpeg4 (default), and msmpeg4.
 +# mpeg1 - gives you files with extension .mpg
 +# mpeg4 or msmpeg4 - gives you files with extension .avi
 +# msmpeg4 is recommended for use with Windows Media Player because
 +# it requires no installation of codec on the Windows client.
 +# swf - gives you a flash film with extension .swf
 +# flv - gives you a flash video with extension .flv
 +# ffv1 - FF video codec 1 for Lossless Encoding ( experimental )
 +# mov - QuickTime ( testing )
 +# ogg - Ogg/Theora ( testing )
 +ffmpeg_video_codec mpeg4
 +
 +# Use ffmpeg to deinterlace video. Necessary if you use an analog camera
 +# and see horizontal combing on moving objects in video or pictures.
 +# (default: off)
 +ffmpeg_deinterlace off
 +
 +############################################################​
 +# SDL Window
 +############################################################​
 +
 +# Number of motion thread to show in SDL Window (default: 0 = disabled)
 +sdl_threadnr 0
 +
 +############################################################​
 +# External pipe to video encoder
 +# Replacement for FFMPEG builtin encoder for ffmpeg_output_movies only.
 +# The options movie_filename and timelapse_filename are also used
 +# by the ffmpeg feature
 +#############################################################​
 +
 +# Bool to enable or disable extpipe (default: off)
 +use_extpipe off
 +
 +# External program (full path and opts) to pipe raw video to
 +# Generally, use '​-'​ for STDIN...
 +;extpipe mencoder -demuxer rawvideo -rawvideo w=320:​h=240:​i420 -ovc x264 -x264encopts bframes=4:​frameref=1:​subq=1:​scenecut=-1:​nob_adapt:​threads=1:​keyint=1000:​8x8dct:​vbv_bufsize=4000:​crf=24:​partitions=i8x8,​i4x4:​vbv_maxrate=800:​no-chroma-me -vf denoise3d=16:​12:​48:​4,​pp=lb -of   avi -o %f.avi - -fps %fps
 +
 +
 +
 +############################################################​
 +# Snapshots (Traditional Periodic Webcam File Output)
 +############################################################​
 +
 +# Make automated snapshot every N seconds (default: 0 = disabled)
 +snapshot_interval 0
 +
 +
 +############################################################​
 +# Text Display
 +# %Y = year, %m = month, %d = date,
 +# %H = hour, %M = minute, %S = second, %T = HH:MM:SS,
 +# %v = event, %q = frame number, %t = thread (camera) number,
 +# %D = changed pixels, %N = noise level, \n = new line,
 +# %i and %J = width and height of motion area,
 +# %K and %L = X and Y coordinates of motion center
 +# %C = value defined by text_event - do not use with text_event!
 +# You can put quotation marks around the text to allow
 +# leading spaces
 +############################################################​
 +
 +# Locate and draw a box around the moving object.
 +# Valid values: on, off, preview (default: off)
 +# Set to '​preview'​ will only draw a box in preview_shot pictures.
 +locate_motion_mode off
 +
 +# Set the look and style of the locate box if enabled.
 +# Valid values: box, redbox, cross, redcross (default: box)
 +# Set to '​box'​ will draw the traditional box.
 +# Set to '​redbox'​ will draw a red box.
 +# Set to '​cross'​ will draw a little cross to mark center.
 +# Set to '​redcross'​ will draw a little red cross to mark center.
 +locate_motion_style box
 +
 +# Draws the timestamp using same options as C function strftime(3)
 +# Default: %Y-%m-%d\n%T = date in ISO format and time in 24 hour clock
 +# Text is placed in lower right corner
 +text_right %Y-%m-%d\n%T-%q
 +
 +# Draw a user defined text on the images using same options as C function strftime(3)
 +# Default: Not defined = no text
 +# Text is placed in lower left corner
 +; text_left CAMERA %t
 +
 +# Draw the number of changed pixed on the images (default: off)
 +# Will normally be set to off except when you setup and adjust the motion settings
 +# Text is placed in upper right corner
 +text_changes off
 +
 +# This option defines the value of the special event conversion specifier %C
 +# You can use any conversion specifier in this option except %C. Date and time
 +# values are from the timestamp of the first image in the current event.
 +# Default: %Y%m%d%H%M%S
 +# The idea is that %C can be used filenames and text_left/​right for creating
 +# a unique identifier for each event.
 +text_event %Y%m%d%H%M%S
 +
 +# Draw characters at twice normal size on images. (default: off)
 +text_double off
 +
 +
 +# Text to include in a JPEG EXIF comment
 +# May be any text, including conversion specifiers.
 +# The EXIF timestamp is included independent of this text.
 +;exif_text %i%J/%K%L
 +
 +############################################################​
 +# Target Directories and filenames For Images And Films
 +# For the options snapshot_, picture_, movie_ and timelapse_filename
 +# you can use conversion specifiers
 +# %Y = year, %m = month, %d = date,
 +# %H = hour, %M = minute, %S = second,
 +# %v = event, %q = frame number, %t = thread (camera) number,
 +# %D = changed pixels, %N = noise level,
 +# %i and %J = width and height of motion area,
 +# %K and %L = X and Y coordinates of motion center
 +# %C = value defined by text_event
 +# Quotation marks round string are allowed.
 +############################################################​
 +
 +# Target base directory for pictures and films
 +# Recommended to use absolute path. (Default: current working directory)
 +#target_dir /​var/​lib/​motion
 +target_dir /​home/​pi/​motion
 +# File path for snapshots (jpeg or ppm) relative to target_dir
 +# Default: %v-%Y%m%d%H%M%S-snapshot
 +# Default value is equivalent to legacy oldlayout option
 +# For Motion 3.0 compatible mode choose: %Y/​%m/​%d/​%H/​%M/​%S-snapshot
 +# File extension .jpg or .ppm is automatically added so do not include this.
 +# Note: A symbolic link called lastsnap.jpg created in the target_dir will always
 +# point to the latest snapshot, unless snapshot_filename is exactly '​lastsnap'​
 +snapshot_filename %v-%Y%m%d%H%M%S-snapshot
 +
 +# File path for motion triggered images (jpeg or ppm) relative to target_dir
 +# Default: %v-%Y%m%d%H%M%S-%q
 +# Default value is equivalent to legacy oldlayout option
 +# For Motion 3.0 compatible mode choose: %Y/​%m/​%d/​%H/​%M/​%S-%q
 +# File extension .jpg or .ppm is automatically added so do not include this
 +# Set to '​preview'​ together with best-preview feature enables special naming
 +# convention for preview shots. See motion guide for details
 +picture_filename %v-%Y%m%d%H%M%S-%q
 +
 +# File path for motion triggered ffmpeg films (movies) relative to target_dir
 +# Default: %v-%Y%m%d%H%M%S
 +# Default value is equivalent to legacy oldlayout option
 +# For Motion 3.0 compatible mode choose: %Y/​%m/​%d/​%H%M%S
 +# File extension .mpg or .avi is automatically added so do not include this
 +# This option was previously called ffmpeg_filename
 +movie_filename %v-%Y%m%d%H%M%S
 +
 +# File path for timelapse movies relative to target_dir
 +# Default: %Y%m%d-timelapse
 +# Default value is near equivalent to legacy oldlayout option
 +# For Motion 3.0 compatible mode choose: %Y/​%m/​%d-timelapse
 +# File extension .mpg is automatically added so do not include this
 +timelapse_filename %Y%m%d-timelapse
 +
 +############################################################​
 +# Global Network Options
 +############################################################​
 +# Enable or disable IPV6 for http control and stream (default: off )
 +ipv6_enabled off
 +
 +############################################################​
 +# Live Stream Server
 +############################################################​
 +
 +# The mini-http server listens to this port for requests (default: 0 = disabled)
 +stream_port 8081
 +
 +# Quality of the jpeg (in percent) images produced (default: 50)
 +stream_quality 50
 +
 +# Output frames at 1 fps when no motion is detected and increase to the
 +# rate given by stream_maxrate when motion is detected (default: off)
 +stream_motion off
 +
 +# Maximum framerate for stream streams (default: 1)
 +stream_maxrate 1
 +
 +# Restrict stream connections to localhost only (default: on)
 +stream_localhost off
 +
 +# Limits the number of images per connection (default: 0 = unlimited)
 +# Number can be defined by multiplying actual stream rate by desired number of seconds
 +# Actual stream rate is the smallest of the numbers framerate and stream_maxrate
 +stream_limit 0
 +
 +# Set the authentication method (default: 0)
 +# 0 = disabled
 +# 1 = Basic authentication
 +# 2 = MD5 digest (the safer authentication)
 +stream_auth_method 0
 +
 +# Authentication for the stream. Syntax username:​password
 +# Default: not defined (Disabled)
 +; stream_authentication username:​password
 +
 +
 +############################################################​
 +# HTTP Based Control
 +############################################################​
 +
 +# TCP/IP port for the http server to listen on (default: 0 = disabled)
 +webcontrol_port 8080
 +
 +# Restrict control connections to localhost only (default: on)
 +webcontrol_localhost on
 +
 +# Output for http server, select off to choose raw text plain (default: on)
 +webcontrol_html_output on
 +
 +# Authentication for the http based control. Syntax username:​password
 +# Default: not defined (Disabled)
 +; webcontrol_authentication username:​password
 +
 +
 +############################################################​
 +# Tracking (Pan/Tilt)
 +#############################################################​
 +
 +# Type of tracker (0=none (default), 1=stepper, 2=iomojo, 3=pwc, 4=generic, 5=uvcvideo, 6=servo)
 +# The generic type enables the definition of motion center and motion size to
 +# be used with the conversion specifiers for options like on_motion_detected
 +track_type 0
 +
 +# Enable auto tracking (default: off)
 +track_auto off
 +
 +# Serial port of motor (default: none)
 +;track_port /dev/ttyS0
 +
 +# Motor number for x-axis (default: 0)
 +;​track_motorx 0
 +
 +# Set motorx reverse (default: 0)
 +;​track_motorx_reverse 0
 +
 +# Motor number for y-axis (default: 0)
 +;​track_motory 1
 +
 +# Set motory reverse (default: 0)
 +;​track_motory_reverse 0
 +
 +# Maximum value on x-axis (default: 0)
 +;track_maxx 200
 +
 +# Minimum value on x-axis (default: 0)
 +;track_minx 50
 +
 +# Maximum value on y-axis (default: 0)
 +;track_maxy 200
 +
 +# Minimum value on y-axis (default: 0)
 +;track_miny 50
 +
 +# Center value on x-axis (default: 0)
 +;​track_homex 128
 +
 +# Center value on y-axis (default: 0)
 +;​track_homey 128
 +
 +# ID of an iomojo camera if used (default: 0)
 +track_iomojo_id 0
 +
 +# Angle in degrees the camera moves per step on the X-axis
 +# with auto-track (default: 10)
 +# Currently only used with pwc type cameras
 +track_step_angle_x 10
 +
 +# Angle in degrees the camera moves per step on the Y-axis
 +# with auto-track (default: 10)
 +# Currently only used with pwc type cameras
 +track_step_angle_y 10
 +
 +# Delay to wait for after tracking movement as number
 +# of picture frames (default: 10)
 +track_move_wait 10
 +
 +# Speed to set the motor to (stepper motor option) (default: 255)
 +track_speed 255
 +
 +# Number of steps to make (stepper motor option) (default: 40)
 +track_stepsize 40
 +
 +
 +############################################################​
 +# External Commands, Warnings and Logging:
 +# You can use conversion specifiers for the on_xxxx commands
 +# %Y = year, %m = month, %d = date,
 +# %H = hour, %M = minute, %S = second,
 +# %v = event, %q = frame number, %t = thread (camera) number,
 +# %D = changed pixels, %N = noise level,
 +# %i and %J = width and height of motion area,
 +# %K and %L = X and Y coordinates of motion center
 +# %C = value defined by text_event
 +# %f = filename with full path
 +# %n = number indicating filetype
 +# Both %f and %n are only defined for on_picture_save,​
 +# on_movie_start and on_movie_end
 +# Quotation marks round string are allowed.
 +############################################################​
 +
 +# Do not sound beeps when detecting motion (default: on)
 +# Note: Motion never beeps when running in daemon mode.
 +quiet on
 +
 +# Command to be executed when an event starts. (default: none)
 +# An event starts at first motion detected after a period of no motion defined by event_gap
 +; on_event_start value
 +
 +# Command to be executed when an event ends after a period of no motion
 +# (default: none). The period of no motion is defined by option event_gap.
 +; on_event_end value
 +
 +# Command to be executed when a picture (.ppm|.jpg) is saved (default: none)
 +# To give the filename as an argument to a command append it with %f
 +; on_picture_save value
 +
 +# Command to be executed when a motion frame is detected (default: none)
 +; on_motion_detected value
 +
 +# Command to be executed when motion in a predefined area is detected
 +# Check option '​area_detect'​. ​  ​(default:​ none)
 +; on_area_detected value
 +
 +# Command to be executed when a movie file (.mpg|.avi) is created. (default: none)
 +# To give the filename as an argument to a command append it with %f
 +; on_movie_start value
 +
 +# Command to be executed when a movie file (.mpg|.avi) is closed. (default: none)
 +# To give the filename as an argument to a command append it with %f
 +; on_movie_end value
 +
 +# Command to be executed when a camera can't be opened or if it is lost
 +# NOTE: There is situations when motion don't detect a lost camera!
 +# It depends on the driver, some drivers dosn't detect a lost camera at all
 +# Some hangs the motion thread. Some even hangs the PC! (default: none)
 +; on_camera_lost value
 +
 +#####################################################################​
 +# Common Options for database features.
 +# Options require database options to be active also.
 +#####################################################################​
 +
 +# Log to the database when creating motion triggered picture file  (default: on)
 +; sql_log_picture on
 +
 +# Log to the database when creating a snapshot image file (default: on)
 +; sql_log_snapshot on
 +
 +# Log to the database when creating motion triggered movie file (default: off)
 +; sql_log_movie off
 +
 +# Log to the database when creating timelapse movies file (default: off)
 +; sql_log_timelapse off
 +
 +# SQL query string that is sent to the database
 +# Use same conversion specifiers has for text features
 +# Additional special conversion specifiers are
 +# %n = the number representing the file_type
 +# %f = filename with full path
 +# Default value:
 +# Create tables :
 +## 
 +# Mysql
 +# CREATE TABLE security (camera int, filename char(80) not null, frame int, file_type int, time_stamp timestamp(14),​ event_time_stamp timestamp(14));​
 +#
 +# Postgresql
 +# CREATE TABLE security (camera int, filename char(80) not null, frame int, file_type int, time_stamp timestamp without time zone, event_time_stamp timestamp without time zone);
 +#
 +# insert into security(camera,​ filename, frame, file_type, time_stamp, text_event) values('​%t',​ '​%f',​ '​%q',​ '​%n',​ '​%Y-%m-%d %T', '​%C'​)
 +; sql_query insert into security(camera,​ filename, frame, file_type, time_stamp, event_time_stamp) values('​%t',​ '​%f',​ '​%q',​ '​%n',​ '​%Y-%m-%d %T', '​%C'​)
 +
 +
 +############################################################​
 +# Database Options
 +############################################################​
 +
 +# database type : mysql, postgresql, sqlite3 (default : not defined)
 +; database_type value
 +
 +# database to log to (default: not defined)
 +; database_dbname value
 +
 +# The host on which the database is located (default: localhost)
 +; database_host value
 +
 +# User account name for database (default: not defined)
 +; database_user value
 +
 +# User password for database (default: not defined)
 +; database_password value
 +
 +# Port on which the database is located
 +#  mysql 3306 , postgresql 5432 (default: not defined)
 +; database_port value
 +
 +############################################################​
 +# Database Options For SQLite3
 +############################################################​
 +
 +# SQLite3 database (file path) (default: not defined)
 +; sqlite3_db value
 +
 +
 +
 +############################################################​
 +# Video Loopback Device (vloopback project)
 +############################################################​
 +
 +# Output images to a video4linux loopback device
 +# The value '​-'​ means next available (default: not defined)
 +; video_pipe value
 +
 +# Output motion images to a video4linux loopback device
 +# The value '​-'​ means next available (default: not defined)
 +; motion_video_pipe value
 +
 +
 +##############################################################​
 +# Thread config files - One for each camera.
 +# Except if only one camera - You only need this config file.
 +# If you have more than one camera you MUST define one thread
 +# config file for each camera in addition to this config file.
 +##############################################################​
 +
 +# Remember: If you have more than one camera you must have one
 +# thread file for each camera. E.g. 2 cameras requires 3 files:
 +# This motion.conf file AND thread1.conf and thread2.conf.
 +# Only put the options that are unique to each camera in the
 +# thread config files.
 +; thread /​etc/​motion/​thread1.conf
 +; thread /​etc/​motion/​thread2.conf
 +; thread /​etc/​motion/​thread3.conf
 +; thread /​etc/​motion/​thread4.conf
 +
 +</​code>​
motion.txt · Последние изменения: 2017/05/29 16:32 — Sergey Kondrashov